50/50 Basic Soap Recipe
A 50/50 soap recipe is one of the first soap recipes we teach to our beginner soap makers in our soap workshops. It is a quick and easy recipe to follow and the bar is a hard and bubbly bar with good cleansing properties.
This basic soap contains no fragrance nor essential oil however adding it is recommended as the olive oil can have a desired scent that you may want to mask.
Because its such a basic recipe it can be modified to also add color or other additives such as oatmeal or even charcoal or turmeric. As the name implies this cold process soap making recipe calls for two oils. Coconut Oil and Olive oil at even amounts for a loaf mold.
Cold Process Soap Making
Cold process soap making is easier than many may think. It can be a bit nerve wrecking especially when it comes to handling lye. This corrosive chemical reacts with water and begins to heat up drastically.
It is good to make safety procedures standard and a habit when it comes to making cold process soap. Many soap makers have stated that after making soap for a while it becomes easier and less scary once they stick to safety protocols.
The one key point that is stressed as we teach and we will stress here on this article is the importance of safety in soap making.
You will be working with super heated materials with the potential to cause major skin burns. You must be sure that you are properly prepared. The main ingredient in soap making is sodium hydroxide also known as lye.
The usage of lye in soap making is absolutely needed and has been a subject of debate. How can a handmade soap be natural if a chemical is used?
Sodium Hydroxide - Lye
Sodium hydroxide is an inorganic compound used to emulsify the fats of oils into soap. When used properly in soap there will be no lye left over in the soap as its chemical makeup changes to create the actual soap.
When handling lye be sure to protect your exposed skin. Here are a few items we recommend you have.
- Long sleve shirt
- Long pants
- Closed toe shoes
- Safety Goggles
These items will ensure if there are any accidents such as splashes you will keep your skin safe from the burning sensation of lye.
- Use an appropriate container to hold your lye and to mix your lye water. Heat tempered glass works very well or hard plastic containers.
- When making your lye water remember to add the LYE to the WATER and never the other way around.
- Mix you lye solution in a well ventilated area. The fumes that will arise from mixing water and lye can become noxious to some persons while its chemical scent can burn your nose and make your eyes water.
- Ensure that you are wearing your safety glasses, rubber gloves, long sleeve shirt and pants and close toe shoes. This is to avoid any splashes getting on your skin. Another reason is that if you use a container that cannot handle the heat created by the lye water solution it could break and the entire solution can get on your body.
In some recopies and depending on where in the world you live you may have to pre heat your oils. Oils can also burn the skin when heated hence ensuring that you are safe from splashes or spills is very important.
A few options will be listed below.
This recipe uses Olive and Coconut Oil ONLY
- 16 oz - Olive Oil
- 16 oz - Coconut Oil
- 10 oz - Distilled water (preferable)
- 4.6 oz - lye (NaOH)
- 1.4 oz - fragrance or essential oil (optional)
- 2 tsp - color (optional)
- 2 qt Glass Mixing Bowl
- 16 oz glass measuring cups (TWO)
- Silicone Spatula
- Stick Blender
- Infrared Thermometer
- Steel Whisk (optional)
- 1 tsp measuring spoon
- 42 oz Loaf Mold
- Food grade scale (ounces)
1 - Lye water
Remember to observe the safety protocol for handling sodium hydroxide. Add lye to water (never the other way around) slowly mix until dissolved.
When mixing you can use your silicone spatula or steel whisk. To ensure an even harder bar and to make it easer to remove from the mold add sodium Lactate to the lye water mix.
Because lye water gets super heated to sometimes over 200 degrees its best to let cool to 80-100deg. (Can put in freezer to speed cooling). Preparing your lye water first will give it time to cool as you prepare other portions of the soap making process.
2 - Oils
Add all of your oils in together in 2 qt large bowl. Depending on where you live your coconut oil may solidify due to cooler weather, if this happens warm to a point where oils are clear and blended
Take note to keep the temperature below 120 deg. 100-110 degrees is good however its good to note that the coconut oil sold by Bahamas Candle and Soap melts at 76 degrees.
3 – Add Essential or Fragrance Oils (optional)
Measure out oils in a glass container. (do not use plastic container for essential oils) When measuring use wax paper on top of your scale to avoid the oil spilling on the plastic of the scale. Essential oil eats at plastic and will destroy your scale
- Add your color to oils and mix with stick blender until well blended
- Add your Fragrance or Essential Oil to base oils and blend together
- Add lye water to Oil mix along stick blender to prevent bubbles Add around 100 deg for oil and lye water
- Depending on your essential or fragrance oil, trace may accelerate be sure to work quickly and blend to light trace.
- Pour mixture into loaf mold, design the top as needed
- Depending on ambient temperature Cover with cardboard or wax paper over top then put to bed with towels to go through trace. If in a room at 75deg or more leave open and exposed. If in a cooler room cover the soap to let its own heat help take it to gel phase for brighter colors.
- Let you soap sit for 24 hours before removing from the mold. Check by pressing lightly on the top of the soap. It should be hard to the touch.
- Remove the soap from the silicone mold and cut in to bars.
- Let your soap bars sit in a cool dry place for 4-6 weeks to cure.
- Curing removes the excess water from the soap, this causes the soap to last longer.
5 - Soap Cutting
Cutting your soap is completely up to you. You can cut as thick or as thin as you like. The most standard thickness is often at 1 inch. For a typical soap loaf this will yeild 10 bars of soap.
The best time to cut a 50/50 soap is the next day, typically 24 hours. With the amount of coconut oil in the soap means that the overall soap will get harder faster than normal. usually by the first week of curing it becomes harder to cut such a soap.
Another popular way to cut soap for gifts is to cut at one inch thick and then take each bar and cut in half. This way you have 20 small gift size bars of soap.
Tools to cut soap can be a semi sharp knife such as the hard plastic type. A common cutter is the soap cutter. Soap cutters are hard metal devices with a wooden handle to push through a soap to make bars.
The last type of cutter are apparatus made with a wire that allows an easy, even and clean cut on each bar of soap.
Make your soap
Congratulations you have made you first basic soap. Be sure to practice a few more times to ensure you get the technique down pat. We also carry soap making kits that are great to get started with if this is your first time making cold process soap.